一本精品热在线视频,久久免费视频分类,精品婷婷乱码久久久久久蜜桃,在线可以免费观看的Av

<mark id="vd61v"><dl id="vd61v"></dl></mark>
    <sub id="vd61v"><ol id="vd61v"></ol></sub>

  • <sub id="vd61v"><ol id="vd61v"></ol></sub>
    "); //-->

    博客專欄

    EEPW首頁 > 博客 > OLED 顯示雷達數據

    OLED 顯示雷達數據

    發布人:無垠的廣袤 時間:2024-12-10 來源:工程師 發布文章
    OLED 顯示雷達數據

    本文結合之前關于串口打印雷達監測數據的研究,進一步擴展至 OLED 屏幕顯示。

    該項目整體分為兩部分:

    • 一、框架顯示;

    • 二、數據采集與填充顯示。

    為了減小 MCU 負擔,采用 局部刷新 的方案。

    1. 顯示框架

    所需庫函數 Wire.h 、Adafruit_GFX.h 、Adafruit_SSD1306.h .

    代碼
    #include <Wire.h>
    #include <Adafruit_GFX.h>
    #include <Adafruit_SSD1306.h>
    #include "logo_128x64.h"
    #include "logo_95x32.h"
    
    #define OLED_RESET 4
    Adafruit_SSD1306 display(128, 64, &Wire, OLED_RESET);
    
    void setup()
    {
      Serial.begin(115200);
      display.begin(SSD1306_SWITCHCAPVCC, 0x3C);  // initialize with the I2C addr 0x3C (for the 128x64)
      display.clearDisplay(); // 清屏
      display.drawBitmap(0, 0, logo, 128, 64, 1); //畫出字符對應點陣數據
      display.display();
      delay(1000);
      display.clearDisplay();
      /*-------------------- Display picture and text ---------------------------*/
      display.drawBitmap(16, 0, logo_small, 95, 32, 1);
      display.setTextColor(WHITE);  //設置字體顏色
      display.setTextSize(2);  //設置字體大小 1 is default 6x8, 2 is 12x16, 3 is 18x24
      display.setCursor(0,33); //設置起始光標
      display.print("v=");
      display.setCursor(72,33); //設置起始光標
      display.print("km/h");
      display.setCursor(0,49); //設置起始光標
      display.print("str=");
      display.display();
    }
    
    void loop()
    {
    }
    效果



    OLED_frame.gif



    2. 顯示數據

    目標:實現雷達監測數據的對應填充顯示,包括速度 v 和信號強度 str


    代碼

    思路:將之前帖子中實現的串口打印數據與 OLED 顯示框架結合,將 vstr 兩數據分別填充至 OLED 屏預留位置處即可。


    #include <Wire.h>
    #include <Adafruit_GFX.h>
    #include <Adafruit_SSD1306.h>
    #include "logo_128x64.h"
    #include "logo_95x32.h"
    
    #define OLED_RESET 4
    Adafruit_SSD1306 display(128, 64, &Wire, OLED_RESET);
    
    String comdata = "";
    
    void setup()
    {
      Serial.begin(115200);
      while (Serial.read() >= 0){}//clear serialbuffer
      display.begin(SSD1306_SWITCHCAPVCC, 0x3C);  // initialize with the I2C addr 0x3C (for the 128x64)
      display.clearDisplay(); // 清屏
      display.drawBitmap(0, 0, logo, 128, 64, 1); //畫出字符對應點陣數據
      display.display();
      delay(1000);
      display.clearDisplay();
      /*-------------------- Display picture and text ---------------------------*/
      display.drawBitmap(16, 0, logo_small, 95, 32, 1);
      display.setTextColor(WHITE);  //設置字體顏色
      display.setTextSize(2);  //設置字體大小 1 is default 6x8, 2 is 12x16, 3 is 18x24
      display.setCursor(0,33); //設置起始光標
      display.print("v=");
      display.setCursor(80,33); //設置起始光標
      display.print("km/h");
      display.setCursor(0,49); //設置起始光標
      display.print("str=");
      display.display();
    }
    
    void loop()
    {
      if (Serial.available() > 0) 
      {
        char data = Serial.read();
        comdata += data;
        if (data == '\n')
        {// type of comdata: v=1.0 km/h, str=10151
          int separatorIndex = comdata.indexOf(','); // 假設分隔符為逗號
          if (separatorIndex != -1)
          {
            String part1 = comdata.substring(0, separatorIndex); // 第一個部分
            String part2 = comdata.substring(separatorIndex + 1); // 第二個部分
            // 打印分割后的數據
            //Serial.println(part1); // type of part1: v=1.0 km/h
            //Serial.println(part2); // type of part2:  str=10151
            /*------------ part1 : v=1.0 km/h ----------*/
            int part1separatorIndex = part1.indexOf('='); //index of '='
            if (part1separatorIndex != -1)
            {
              String vlc = part1.substring(part1separatorIndex + 1); // index of velocity, type of vlc is 1.0 km/h
              // vlc: 1.0 km/h
              int VLCseparatorIndex = vlc.indexOf(' '); // index of ' '
              String v = vlc.substring(0, VLCseparatorIndex);// v only include number
              float Vn = v.toFloat();
              Serial.print(Vn); // print velocity number
              Serial.print(',');
              //display.setCursor(25,33); //設置起始光標
              display.fillRect(25, 33, 60, 16, BLACK);
              display.display();
              display.setCursor(25,33); //設置起始光標
              display.print(Vn);
              display.display();
            }
            /*------------- part2 :  str=10151 ------------------*/
            int part2separatorIndex = part2.indexOf('='); //index of '='
            if (part2separatorIndex != -1)
            {
              String strng = part2.substring(part2separatorIndex + 1); // strng only include number
              int Sn = strng.toInt();
              Serial.print(Sn); // print strength number
              Serial.println();
              //display.setCursor(49,49); //設置起始光標
              display.fillRect(49, 49, 79, 16, BLACK);
              //display.setPixelColor();
              display.display();
              display.setCursor(49,49); //設置起始光標
              display.print(Sn);
              display.display();
            }
          }
          comdata = "";
        }
      }
    }


    效果

    這里由于字體設置為 2 號,無法滿足 km/h 單位的完整填充,因此被數據覆蓋住一部分,可根據實際需求調整字體大小。

    UART_plot.gif

    同時支持串口繪圖和串口數據打印。


    *博客內容為網友個人發布,僅代表博主個人觀點,如有侵權請聯系工作人員刪除。



    關鍵詞: 雷達 Arduino OLED 串口

    相關推薦

    技術專區

    關閉